Permanent gel - 

Aqua (Water), Ammonium Thioglycolate, Ammonium Bicarbonate, Ammonium Acryloyldimethyltaurate/VP Copolymer, Dipropylene Glycol, Hydrolyzed Collagen, Ammonia, Ethanolamine, Disodium EDTA, Boswellia Serrata Gum, Sodium Hydrosulfite, Phenoxyethanol, Sodium Hydroxide, Benzoic Acid, Sodium Benzoate.

Neutraliser - 

Aqua (Water), Cetearyl Alcohol, Stearyl Alcohol, Cetyl Alcohol, Hydrogen Peroxide, Ceteareth-33, Aminotrimethylene Phosphonic Acid, Sodium Stannate, Phosphoric Acid

Regen -

 Paraffinum Liquidum, Ricinus Communis Seed Oil, Gallic Acid, Paraffin, Argania Spinosa Kernel Oil, Helianthus Annuus Seed Oil, Zea Mays Germ Oil, Olea Europaea Fuit Oil, Vitis Vinifera Fruit Extract, Rosa Canina Fruit Extract, Decyl Oleate, Tocopherol.

Permanent Gel -
Apply all over the hair for 10/15 min depending on hair thickness, making sure the product is covering the hair from root to tip. Cover with cling wrap and check how the product is working after 5 min. Remove with a dry cotton pad before applying step 2.

Processing times:
Thin hair - 7/9 min
Med hair - 9/12 min
Thick hair - up to 15min

Neutraliser Cream -
Apply all over the hair for the exact same time as the first solution. Brush the hair in the correct shape you're trying to achieve and cover it with cling film. Use a damp cotton pad to remove all products. Dry the brows by using a second dry cotton round. At this point, you can tint/dye and wax!

Regenerating Cream -
Apply all over the brows with a lip wand and ask your clients to not wash the product for 24hrs and avoid hot water, steam baths and saunas). This product is also a great aftercare to retail to your client!

Step 1 -
Thoroughly clean the eye area with a gentle foam shampoo then dry any excess moisture with a tissue. Apply the adhesive on the eyelid, as close to the lash line as possible, without touching the lashes

Step 2 -
Stretch and curve the Thuya Silicone Pads, that will help to adapt them better to the eyelids and adhere it on the glue. Press down and hold for a minute so it can set and dry on the eyelid. Apply the adhesive on the shield and lift the lashes with an upward motion. Make sure the lashes are separated and lined up in the same direction for the best results.

Step 3 -
Apply Permanent Gel (always dispose of the first drop of product). Spread the product from the base to the middle part of the eyelid, leaving approximately 1mm from the lash line. Cover the eyelashes with cling wrap and let it process for UP TO 15 minutes depending on hair thickness. Then remove the product with a dry cotton swab.

Step 4 -
Apply Neutraliser Cream and Spread the product from the base to the middle part of the eyelid, leaving approximately 1mm from the lash line. Cover the eyelashes with cling wrap and let it process for the same amount of time as the permanent gel. Then remove the product with a dry cotton swab.

Step 5 -
Apply Protector Paper on the lower part of the eye making sure the lower eyelashes are on top of the Protector Paper. Mix the Thuya Dye and the special Dye Solution (1:1 ratio). Apply the mix on the eyelashes and let it act for 15 minutes. After the exposure time, remove the excess product with a dry cotton swab followed by a damp cotton pad making sure all tint is fully removed.

Step 6 -
To finalise the service, apply the Lash Filler BTX on the lashes from root to tip by using a micro brush. Leave it on for 15 minutes. After the exposure time, remove any excess with a mascara brush.